Breakers That Keep Tripping
A breaker that won't stay set is doing its job — warning you a circuit is overloaded, shorted or faulting. We find which device or connection is drawing too much and fix the cause, not just reset the switch.
Electrical Service
Electrical Repairs
Dead outlets, tripping breakers, flickering lights or a smell you can't place? Precision Power's NYC electricians diagnose the real cause fast and fix it right — same-day service on most repairs, with honest, upfront pricing.
Troubleshooting & Repair
We Find the Real Cause — and Fix It
Most electrical problems are a symptom, not the disease. A dead outlet, a breaker that won't stay set, lights that flicker when the AC kicks on — each one points back to a fault somewhere in your wiring, devices or panel. Replacing the part you can see without finding why it failed just buys a few weeks before it happens again, sometimes with a worse outcome.
Precision Power's NYC-licensed electricians do real diagnostic work: we trace the circuit, test under load, and isolate the fault before we touch a thing. Then we repair the root cause — a failed device, a loose or overheated connection, an undersized circuit, a bad breaker — and correct any code issues we uncover along the way. Most repairs are handled the same day, and you get a clear price before we start.
- Outlets, switches & light fixtures repaired or replaced
- Tripping breakers & panel faults diagnosed and fixed
- Flickering / dimming light diagnosis & correction
- Fault-finding & code corrections, done to NYC standards
SAMEDAY
Common Faults
Problems We Fix
From the everyday annoyance to the genuine fire risk — here's what we get called out for, and what each one is usually telling you.
Dead Outlets or Switches
An outlet or switch that's gone dead usually means a tripped GFCI, a worn device, or a loose connection upstream. We trace the circuit, find the break, and replace or re-terminate what failed.
Flickering or Dimming Lights
Lights that flicker or dim when an appliance kicks on point to voltage drop, a loose neutral or an overloaded circuit. It's an early warning of a connection problem we can pinpoint and repair.
Burning Smell or Scorch Marks
An acrid burning smell or browning around an outlet, switch or panel means a connection is overheating or arcing behind the wall. This one can't wait — kill the circuit if you safely can and call us right away.
Warm Outlet or Switch Plates
A cover plate that's warm to the touch is a red flag — a loose terminal or failing device is generating heat where there should be none. Left alone, that heat is how electrical fires start.
Buzzing or Crackling Sounds
Buzzing or crackling from an outlet, switch or panel is the sound of electricity arcing across a loose or damaged connection. It's never normal — switch it off and have it inspected the same day.
Don't Wait — Act Now
Stop & Call Us Now If…
Some electrical faults are inconvenient. These three are dangerous — they signal an active fire or shock risk and need an electrician immediately, not tomorrow.
Burning Smell or Smoke
Fire risk
A burning or melting-plastic smell, or any smoke from an outlet or panel, means wiring is overheating right now. Cut the power if you safely can and call immediately.
Sparks or an Electric Shock
Danger
Sparks from an outlet, or a shock or tingle from a switch, appliance or faceplate, means a live fault is exposed. Stop using it and get it looked at right away.
Exposed or Hot Wires
Urgent
Bare, damaged or noticeably hot wiring is an immediate shock and fire hazard. Keep people and water away, kill the breaker if you can, and call us now.
These can't wait — call (332) 290-3178, 24/7.
Our Approach
How We Diagnose & Fix It
Good electrical repair starts with diagnosis, not a guess. When we arrive, we listen to what's happening and when, then do systematic fault-finding — testing the circuit, checking it under load, and isolating the fault to a specific device, connection or run before we open the toolbag for the fix. That's the difference between a repair that lasts and one that comes back.
We fix the root cause, not the symptom
Swapping a dead outlet is easy. Finding out why it died — a loose backstab, an overloaded circuit, a failing connection two boxes upstream — is the part that actually keeps it from happening again. We fix the cause so the same fault doesn't resurface a month later.
We correct code issues we find
Older NYC homes hide a lot behind the walls: ungrounded outlets, missing GFCI/AFCI protection, over-fused circuits, sloppy past work. When a repair exposes something that's out of code, we tell you and put it right, so the circuit is safe and compliant when we leave.
We're honest about repair vs. replace
Sometimes a fault is a symptom of something bigger — aging wiring at the end of its life, or a panel that can't keep up. If a repair would only be a band-aid, we'll tell you straight that a rewire or a panel upgrade is the real fix, and why. No upsell, just the honest call.
Honest Pricing
What Drives the Cost of a Repair
No two electrical faults are the same, so we quote after we diagnose. These are the factors that move the number.
Diagnosis Time
A clear dead outlet is quick to trace. An intermittent fault or a flickering circuit can take real diagnostic time to isolate before any repair begins.
Parts Needed
Replacing a single outlet, switch or breaker is inexpensive; a specialty device, a smart switch or a hard-to-source breaker costs more.
Access
A fault behind finished walls, in a tight ceiling or several floors up takes longer to reach and repair cleanly than an exposed junction.
Root Cause
Swapping a failed device is one job; if the cause is the wiring itself — a bad run, a failing neutral — the fix is larger than the part you can see.
Code Corrections
If the repair uncovers ungrounded wiring, missing GFCI/AFCI protection or over-fused circuits, making it safe and compliant adds to the work.
After-Hours / Emergency
A true emergency call outside normal hours carries a different rate than a scheduled daytime visit — but you'll always know it before we start.
The honest version: there's no flat price for an electrical repair — the same "dead outlet" can be a quick fix or a buried wiring fault. That's why we diagnose first, explain exactly what's wrong, and give you a clear price before any repair work begins. No surprise line items at the end.
Our Process
How a Repair Visit Works
Diagnose first, quote before we touch it, repair the cause, then prove it's fixed.
1
Diagnose
We listen to the symptoms, trace and test the circuit, and isolate the real fault before we recommend any work.
2
Upfront Quote
You get a clear price for the fix — and any code corrections we found — explained in plain language before we start.
3
Repair
We fix the root cause to NYC code — replacing devices, re-terminating connections or correcting wiring as needed.
4
Test & Verify
We power the circuit back up, test it under load, confirm the fault is gone, and leave the area clean.
Precision Power
Fixed Right, the First Time
We don't chase symptoms — we find the fault and repair the cause, so the same problem doesn't come back next month.
Call (332) 290-3178Where We Work
Electrical Repairs Across New York
Licensed electricians serving every borough and the surrounding counties.
Questions
Electrical Repair FAQs
Straight answers to the questions we hear most.
Why does my breaker keep tripping?
A breaker trips to protect you, so a repeat trip means something on that circuit is wrong — usually an overload (too much plugged in), a short circuit, a ground fault, or a failing breaker itself. Resetting it over and over doesn't fix the cause and can let heat build. We test the circuit, find which of those it is, and repair it properly.
Why are my lights flickering?
Occasional flicker on one fixture is often a loose bulb or a dimmer mismatch. But lights that flicker or dim across a room — especially when an appliance starts — point to a loose connection, a bad neutral or an overloaded circuit. Those are worth diagnosing, because the same loose connection that flickers a light can also overheat. We can pinpoint which it is.
Is a burning smell an emergency?
Yes. An acrid, burning-plastic smell from an outlet, switch or panel means a connection is overheating right now, and that's how electrical fires start. Switch off the breaker for that area if you can do so safely, stop using it, and call us immediately — this is exactly the kind of call we take 24/7.
Can you do same-day repairs?
Most repairs, yes. Common faults — dead outlets, bad breakers, faulty switches and fixtures, flickering circuits — we diagnose and fix on the same visit. If a repair needs a specialty part or turns out to be a larger job, we'll tell you on the spot and schedule it quickly.
Do you handle small jobs?
Absolutely. A single dead outlet, one flickering fixture or a switch that's stopped working is a perfectly normal call for us. No job is too small — and small faults are often early warnings of a bigger problem, so it's worth getting them looked at.
How do you decide repair vs. replace or upgrade?
We repair whenever a repair will genuinely solve the problem and hold up. But if a fault is a symptom of aging wiring at the end of its life, or a panel that can't keep up with your home's load, we'll tell you honestly that a rewire or panel upgrade is the real fix — and explain why — rather than charge you for a band-aid that comes back.
Are two-prong (ungrounded) outlets a problem?
They can be. Two-prong outlets have no ground, which means no protection path for faults and no safe grounding for electronics or surge protectors. Depending on what's behind the wall, the fix is either running a ground, or installing GFCI protection where a ground isn't practical. We test what you have and recommend the correct, code-compliant option.
Do you offer 24/7 emergency repairs?
Yes. Burning smells, sparks, shocks, exposed hot wires and sudden power loss don't keep business hours, and neither do we. Call (332) 290-3178 any time — after-hours emergency rates are explained upfront before we start.